In short: RUBS, the ratio utility billing system, divides one utility bill among the homes it serves by a formula, such as the number of occupants, each home's square footage or its number of fixtures, instead of by a meter at each home. Whether it is allowed depends on the state, the utility and the rental agreement.
What RUBS Stands For, and What It Is
RUBS stands for ratio utility billing system. It is a way of sharing one utility bill among the homes that bill covers. The property owner buys the utility for the whole property, works out each home's share by a formula, and bills each resident that share. No meter at the home is involved: the share comes from the formula, not from what the home used.
A national study of the practice, sponsored by the U.S. Environmental Protection Agency together with apartment-industry groups, describes RUBS bills as “prorated from the overall utility master meter bill based on one or a combination of quantitative measures such as square footage, number of occupants, or number of fixtures” (National Multiple Family Submetering and Allocation Billing Program Study, 2004). A master meter is the one utility meter that measures what the whole property used. That study looked at water and sewer bills, and treats RUBS as one kind of what it calls allocation billing.
How a RUBS Charge Is Calculated
A RUBS charge is usually worked out in three steps:
- Start from the utility's bill for the period: the amount the utility charged the property.
- Set aside the share for common areas. Water or power used by the clubhouse, pool, landscaping or office is not any resident's use. Unless the common areas have their own meter, their share is an estimate. In the study's survey of billing companies, 55.6 percent subtracted common-area use for all of their RUBS customers and another 38.9 percent for some. Half of all the companies surveyed set the common-area share as a percentage of total use, typically about 10 to 20 percent (companies could name more than one method).
- Divide the rest among the occupied homes by the formula, and bill each home its share. The study describes the bill as shared among the occupied homes, and its recommended practices have the owner, not the residents, pay for water used in common areas and in vacant homes.
The formula is where methods differ. The study lists formulas based on a home's square footage, number of bedrooms, number of occupants, number of bathrooms or number of fixtures, used alone or in combination. In its survey of billing companies, the most used were the number of residents (94.4 percent of companies) and square footage (83.3 percent), followed by a flat fee (44.4 percent), bedrooms (33.3 percent), fixtures (27.8 percent) and bathrooms (22.2 percent); the “other” methods included combinations. The main formulas work like this:
- Occupancy. Each home's share follows the number of people living in it. A home with 3 of the property's 250 occupants pays 3/250 of the amount shared.
- Square footage. Each home's share follows its floor area as a part of the total floor area of all the homes.
- A combination. Part of the amount is shared by one measure and part by another, for example half by occupancy and half by square footage.
- Fixture count. Each home's share follows its number of water fixtures, such as toilets, sinks and showers.
The study also found that residents are typically charged a service fee on top of the allocated charge, where state and local law allow one.
A Worked Example
This is an illustration with made-up round numbers. It shows the arithmetic only; it does not say that any method is allowed for any utility in any state.
A community of 100 homes, all occupied, receives a water bill of $6,000 for the month. It sets aside an estimated 10% for common areas, so $600 stays with the community and $5,400 is shared among the homes. One home has 3 occupants (of 250 in the community) and 1,400 square feet (of 120,000 in total).
| Formula | This home's share | This home's charge |
|---|---|---|
| Occupancy | 3 of 250 occupants (1.2%) | $5,400 × 3 ÷ 250 = $64.80 |
| Square footage | 1,400 of 120,000 square feet (about 1.17%) | $5,400 × 1,400 ÷ 120,000 = $63.00 |
| Half occupancy, half square footage | Half of each | ($64.80 + $63.00) ÷ 2 = $63.90 |
Each charge uses the exact fraction, not the rounded percentage. Notice what does not appear anywhere in the table: how much water this home actually used. A home whose residents are away half the month pays the same share, and one home's leak raises every home's share.
RUBS vs. Submetering vs. a Flat Charge
Submetering means billing each home from its own meter, called a submeter, which sits past the property's master meter. A flat charge is a set amount that does not change with the bill or with use.
| RUBS | Submetering | Flat charge | |
|---|---|---|---|
| What sets the charge | A formula share of the utility's bill | The home's own meter reading | A set amount |
| Changes with the home's own use | No | Yes | No |
| Meter at each home | Not needed | Needed | Not needed |
| What a resident can check | The bill, the formula and their own share | Their meter readings and the rate | The amount |
The difference shows up in use. The 2004 study, which covered apartment and other multi-family properties, found that submetering cut water use by 15.3 percent compared with properties where water was included in the rent, and concluded that “no statistically significant impact from RUBS could be reliably expected” (National Multiple Family Submetering and Allocation Billing Program Study, 2004).
For a manufactured housing community the three can sit side by side: one utility billed from submeters, another shared by formula where that is allowed, and trash as a flat charge. Each utility follows its own rule.
What Residents See on the Statement
A RUBS charge is fair only if the resident can check it. A clear statement shows, for each shared utility:
- The utility, the billing period and the amount of the bill being shared.
- What was set aside for common areas.
- The formula, and this home's own figures in it (for example, 3 occupants of 250).
- The resulting share, on its own line, apart from rent and other utilities.
- Any service or billing fee, on its own line, where one is allowed.
- Who prepared the bill, and how to reach them with a question.
In California, each separately billed utility charge must be stated separately on the resident's billing (Cal. Civ. Code § 798.41(d)), and a third-party billing company that prepares it is named on it with its address and telephone number (Cal. Civ. Code § 798.40(b)).
Why Manufactured Housing Is Different
Most RUBS writing is about apartments. A manufactured housing community differs in three ways that change the answer.
- It rents spaces, not apartments. A space is the lot a home sits on. The resident may own the home and rent the space. California's Mobilehome Residency Law calls a resident who rents a space under a rental agreement a “homeowner” (Cal. Civ. Code § 798.9), and its utility rules are written for that relationship.
- Some communities are master-metered. Some communities were built with one or a few utility connections, master meters, that serve every home, some with a submeter at each space. In California, the state's Public Utilities Commission has noted that many residents of communities built before 1997 receive their gas or electricity through a master meter and a privately owned submeter system (CPUC Decision 14-03-021, quoting its rulemaking order). Where a submeter exists, each home can be billed for what it used, and in California the law requires it for gas and electricity from an investor-owned utility and for submetered water bought from a water company (see the table below).
- State law speaks to these communities directly. California, for example, has utility-billing rules written only for these communities (Cal. Civ. Code §§ 798.40–798.43.1) on top of the gas and electric rule that also applies to master-metered apartment buildings (Cal. Pub. Util. Code § 739.5).
For how master meters and submeters work, see our master meter vs. submeter guide.
Is RUBS Allowed?
Each state sets its own rules for when a community may bill a utility by formula. Sentinel publishes a state's answer only after researching it to its statutes. California's is below.
California
An investor-owned utility here means a privately owned gas or electric company regulated by the California Public Utilities Commission.
| Utility and setup | RUBS allowed? | Source |
|---|---|---|
| Gas or electricity from an investor-owned utility (including power bought through a local community-choice program), through a master meter | No. Each resident is charged “at the same rate that would be applicable if the user were receiving gas or electricity, or both, directly” from the utility, on an itemized bill showing the meter's opening and closing readings. | Cal. Pub. Util. Code § 739.5(a), (e) |
| Electricity from a local publicly owned utility (for example, a city-owned utility) | It depends on that utility's own rules. In our reading, § 739.5(a)'s rate rule does not reach it: that rule refers to the rate of a gas corporation or a “load-serving entity”, and a local publicly owned electric utility is not a load-serving entity. That utility's own rules govern its rates, and the Mobilehome Residency Law's billing rules still apply (Cal. Civ. Code §§ 798.40(a)–(b), 798.41). | Cal. Pub. Util. Code § 380(k)(1) |
| Water or sewer (the statute counts sewer as water service), bought from a water company through a master meter, at a community with water submeters | No. Management “shall only bill” by the methods the statute lists: a metered share of the community's own water bill, each price tier's volume divided evenly among the spaces, or the water company's own per-space rates, plus the fixed charges (which may be split equally among spaces) and one capped billing fee. A RUBS formula is not one of them. | Cal. Civ. Code § 798.40(c), (d)(3) |
| Water or sewer, at a community with no submeters | Yes, within the statute's limits (our reading of § 798.41(a)): unless the rental agreement specifically provides otherwise (for example, that the utility is included in the rent), shared from the charges the utility assessed, with common-area use left out, no billing fee added, and the shares never more than the bill. No statute expressly approves any formula method. A local rent-control ordinance can count the charge as rent, and so subject to its limits on rent, if the rent was not reduced when separate billing began. Rental agreements made before January 1, 1991 are outside § 798.41 until extended or renewed (§ 798.41(b)). | Cal. Civ. Code § 798.41(a)–(b) |
Our submetering vs. RUBS guide for California works through each row in detail.
Mistakes to Avoid
- Using a formula where the law requires a meter. In California, gas and electricity from an investor-owned utility are billed at the direct rate from the meter's readings (Cal. Pub. Util. Code § 739.5(a), (e)), and submetered water bought from a water company only by the statute's methods (Cal. Civ. Code § 798.40(c)). Check each utility before choosing a method.
- Leaving common-area use in the shared amount. The clubhouse, pool and landscaping are not a resident's use. For submetered water in California the statute says so outright (Cal. Civ. Code § 798.40(c)(1)(D)).
- Sharing more than the bill. The shares should add up to no more than the amount being shared. In California, our reading of § 798.41(a) is that a formula charge is limited to the fees and charges the utility assessed.
- Hiding the formula. A resident who cannot see the bill, the formula and their own figures cannot check the charge, and a charge that cannot be checked is hard to defend.
- Moving a utility out of the rent without lowering the rent. In California, a separately billed utility is kept from counting as rent under a local rent-control ordinance only if, at the first separate bill, the rent is reduced by the average the community was charged for that utility for that space in the 12 months before it gave notice of the separate billing (Cal. Civ. Code § 798.41(a)).
- Expecting RUBS to cut use. The 2004 study of multi-family properties concluded that no statistically significant effect on water use from RUBS could be reliably expected. If the goal is conservation, submetering is the method that study found to work in multi-family properties.
Frequently Asked Questions
What does RUBS stand for?
RUBS stands for ratio utility billing system. It shares one utility bill among the homes it serves by a formula, such as occupants, square footage or fixtures, instead of by a meter at each home.
What is RUBS in real estate?
In rental housing, RUBS is a way for a property owner to bill residents for a utility the owner buys for the whole property. Instead of paying the bill as part of the rent, the owner divides it among the homes by a formula and bills each resident a share.
How is RUBS calculated?
Start with the utility's bill for the period, set aside the share for common areas, and divide the rest among the occupied homes by the formula. With an occupancy formula, a home with 3 of a property's 250 occupants pays 3/250 of the amount being shared.
Is RUBS legal in California?
Only for some utilities. Gas and electricity from an investor-owned utility (a privately owned gas or electric company regulated by the California Public Utilities Commission), including power bought through a local community-choice program, cannot be billed by formula: each resident is charged at the rate they would pay as the utility's direct customer, on a bill showing the meter's opening and closing readings (Cal. Pub. Util. Code § 739.5(a), (e)). Water or sewer bought from a water company through a master meter at a community with water submeters may be billed only by the methods in Cal. Civ. Code § 798.40(c); a RUBS formula is not one of them, and only the fixed charges may be split equally among spaces. Water or sewer at a community with no submeters may be shared by formula within Cal. Civ. Code § 798.41's limits (our reading of § 798.41(a)); no statute expressly approves any formula method.
What is the difference between RUBS and submetering?
Submetering bills each home for what its own meter measured; RUBS bills each home a formula share of the whole bill. With submetering a resident's charge follows the resident's own use, and the resident can check it against the meter.
Can a mobile home park (manufactured housing community) use RUBS for gas or electricity?
Not in California when the gas or electricity comes from an investor-owned utility, including power bought through a local community-choice program: each resident is charged at the utility's direct residential rate, on a bill showing the meter's opening and closing readings (Cal. Pub. Util. Code § 739.5(a), (e)). Other states set their own rules.
Does RUBS reduce water use?
A 2004 national study of apartment and other multi-family properties found no reliable effect. After correcting for other factors, it concluded that no statistically significant impact from RUBS could be reliably expected, while submetering cut water use by 15.3 percent compared with water included in the rent (National Multiple Family Submetering and Allocation Billing Program Study, 2004).
Sources
Every statement of law above cites its section. The market facts come from the national study listed first. Sources read on November 14, 2026.
- National Multiple Family Submetering and Allocation Billing Program Study (Aquacraft, Inc. and others, 2004; sponsored by the U.S. Environmental Protection Agency, the National Apartment Association and the National Multi Housing Council, among others)
- Cal. Pub. Util. Code § 739.5 — master-metered gas and electric service
- Cal. Pub. Util. Code § 380 — the definition of a load-serving entity
- Cal. Civ. Code § 798.40 — statements, rate posting and submetered water
- Cal. Civ. Code § 798.41 — billing utilities separately from rent
- Cal. Civ. Code § 798.9 — who is a homeowner under the Mobilehome Residency Law
- CPUC Decision 14-03-021 (March 13, 2014) — master-metered communities and conversion to direct service